(800) 952-0121          email icon1 

SilverLine™ Smart Cooking System

The latest innovation in steam cooking, the SilverLine Smart Cooking System is the most powerful and versatile steam cooking system available. 3-A certified and meeting EHEDG, CE, and FDA requirements, this stainless steel system can adjust shear mechanically – from low shear to bloom starches to high shear for starch conversion – delivering predictable, precise, and repeatable results with superior quality every time.

Applications:
Soups, sauces, slurries, beverages, dairy-based products, tomato-based products, starch-based products, high or low shear products, blended emulsification, pasteurization, and more...

Volume Capability:
5 up to 200 gpm [1.1 up to 45 m³/hr]

Direct Steam Injection Heating for the Wastewater Industry

Maintaining consistent sludge temperature in the Municipal, Agricultural, or Industrial markets can be challenging. If you are looking for a more efficient, cost-effective solution for heating your sludge without the scalding that can occur with a heat exchanger, then Hydro-Thermal has your solution.

Realize major cost savings with precise temperature control to aid in the anaerobic digestion process by keeping microorganisms at the required temperature to optimize effectiveness and increase methane gas production to power the boilers.

Hydro-Thermal’s patented designs can handle highly viscous slurries without burn on, plugging, or fouling typically resulting from other technologies, achieving thousands of dollars in energy savings.  

Hydro-Thermal's patented DSI heating system works by mixing steam and process liquids completely while delivering consistent temperature and instantaneous heating. For more information on our advanced direct steam injection technology, click here

Applications for Municipal, Agricultural, and Industrial Wastewater

Anaerobic digester sludge heating – recirculation or preheating

A reliable heating source for anaerobic digestion is imperative to ensure production (or capture) of biogas/methane.

What does your plant need from an Anaerobic Digestion Heater?

Heating Flexibility

 

The NOH’s high heating capability and range enable it to transition easily from shutdown to startup to maintenance mode, bringing the anaerobic digester up to temperature with extreme precision.

 

Precise temperatures without fear of scalding

 

Achieve ideal temperatures of 85-100°F (29-38°C) for mesophilic digestion or 120-140°F (49- 60°C) for thermophilic digestion to optimize biogas generation. The NOH provides more efficient way of heating than the conventional heat exchanger.

 

Non-Obstructing Heater (NOH) design that reduces maintenance 

 

The NOH’s straight flow-through design can ensure that rags do not get caught and plug the heater. The NOH can be produced using wear and corrosion resistant metallurgies to withstand grit and highly abrasive materials.

 

Space Savings 

 

The inline design of the NOH frees up valuable plant space.

 

Hydro-Thermal Anaerobic Digestion Heater Solutions

 

Combined with HTC’s NOH design and the process inputs given for the application, Hydro-Thermal has the optimal solution.

Digester Heating - Reclaimed heat with a pump

NOH Digester Heating w pump2d

Digester Preheating

Digester Recirculation Heating

NOH Digester Recirc Heating2d

Click here to learn more by reading our industrial wastewater case study 

Click below to watch a short informative video on the NOH heater

Industrial Pretreatment

Heating during industrial pretreatment is imperative to optimize separation, leading to an increase in oil yield. 

What does your plant need from a Pretreatment Heater? 

Maximize fats, oils, and grease (FOG) extraction while reducing or eliminating breaker chemicals

Hydro-Thermal's non-shear heater will heat the FOG waste stream to the optimal temperature to maximize oil extraction via a centrifuge, decanter, or tricanter process. With precise temperature control, oil yield (and ultimately revenue) can be increased. 

Optimizing oil extraction is governed by Stoke's Law. Several factors make up Stoke's Law. Using Hydro-Thermal's non-shear heater help decrease the viscosity and increase the relative density of the waste oil stream, resulting in increased yield. The added temperature enables a possible reduction in emulsion breaker chemical dosing.

Tank Heating

Easily and efficiently heats tanks on in-feed or in recirc mode (trim heat). We can heat the fluid going into the tank, re-circulate the tank to maintain a specific temperature, or leave the tank cold and heat the liquid exiting the tank, producing hot water on demand.

  • Click here to learn why tank heating is more efficient by utilizing a Hydroheater vs. a sparger.

PDF Resources

      Industrial Pretreatment              Heating Digester Slurries              Anaerobic Digestion                     Wastewater Whitepaper                                       

   Industrial Pretreatment                         Heating Digester slurries                              Anaerobic digestion                       Wastewater whitepaper                     

 

 

Learn More...

For more information on our products, click here.

For more information on our patented direct steam injection technology, click here.

Looking for a quote? Fill out this form.

How Does Direct Steam Injection Work?

Direct Steam Injection works by directly injecting steam into a process fluid to obtain more rapid heat transfer, resulting in more efficient energy usage than indirect heat exchangers. This efficient process of heating is caused by our direct steam injection Hydroheaters ability to control both steam flow and mixing turbulence by using a modulating stem plug and nozzle or diffuser assembly in the heater. This precise mixing of a measured amount of high-velocity steam directly with your liquid or slurry provides an instantaneous heat transfer from steam to the fluid. This heat transfer method allows for 100% thermal efficiency and energy savings of 20-25%. Don’t believe us? Head over to our Energy Savings Calculator to get an accurate estimate of how much you can be saving in operating costs.

A precisely engineered, variable-area steam nozzle or diffuser meters the flow at the point of injection and contact with the fluid. The large pressure drop from full steam pressure to the process fluid pressure ensures high-velocity choked steam flow and instantaneous mixing of the two streams. When steam flow is choked, its velocity at the nozzle or diffuser exit is constant regardless of the total mass flow injected. The internally modulated Hydro-Thermal heaters control the amount of injection area (cross-sectional area of the nozzle or diffuser opening) to regulate the heat load precisely—the constant steam velocity results in consistent and stable operation across the full range of operations.

Hydro-Thermal’s patented direct steam injection heaters use direct heat exchange to transfer 100% of the steam’s energy for heating liquids and slurries over a wide range of viscosities and solid contents to precise temperatures. A Hydroheater’s internal modulation assures exacting steam control and rapid temperature management and produces predictable results. Each Hydro-Thermal heater has an internal trim custom designed for each customer’s specific needs and requirements.

How Direct Steam Injection Works - Hydroheater

Direct Steam Injection Technology

Hydroheaters/Jetcookers commonly outperform other forms of direct steam injection and indirect heating methods such as heat exchangers. Use the links below to learn more about how Hydro-Thermal’s patented technology outperforms the status quo.

  • External Modulation vs Internal Modulation Button
  • Direct Heating vs Indirect Heating Button
  • Types of Direct Steam Injection Button

External vs. Internal Modulation:

Externally or Internally modulated direct steam injection refers to how the mass flow of steam injected into the process fluid is controlled.

External modulation uses a steam control valve on the supply line to vary the pressure of the steam at the point of injection: Varying the pressure changes the steam density and velocity through the nozzle to control the amount of heating. Regulating steam pressure to control heating can result in unstable operation, hammering, and vibration when high or low steam flowrates are required. At low steam flow, i.e., trim heating, the differential between steam pressure and the process can be very small, and a slight fluctuation in either pressure can cause an upset. Alternatively, at high steam flow requirements, i.e., max heating at startup, the orifice or nozzle size will allow more steam than can be condensed, and steam hammer occurs.

Internally modulated DSI controls the injection area rather than steam velocity and density to regulate the amount of heating. An internally modulated heater operates at higher steam velocities compared to external modulation. This higher velocity produces improved, often rapid mixing and nearly instantaneous condensation of the steam into the process fluid.

External Modulation
Internal Modulation

External Modulation

Internal Modulation

Direct vs. Indirect Heating:

There are two basic types of heat exchangers used to transfer heat between process fluids — direct heat exchange and indirect. Indirect heating is most commonly seen in the form of plate & frame or shell & tube heat exchangers. Any process that does not allow direct mixing of steam and fluid is indirect heating. Heat exchangers transfer heat through a membrane or solid wall. This results in only ~ 83% of the heat energy transferred to the process fluid. In contrast, the remaining energy is discharged in the condensate formed from the steam.

On the other hand, direct heating uses 100% of the steam’s heat energy by adding steam directly to the process fluid.

The benefits of using direct contact heating vs. indirect include:
  • Energy savings of 25% or more
  • Precise and instantaneous temperature control is possible to within 1°F
  • Reduced footprint for direct steam injection system
  • Reduces maintenance via self-cleaning and elimination of a condensate return system
Additional benefits:
  • Rapid and uniform heating -important in starches and food product
  • Can heat highly viscous fluid
  • Handles fluids that are difficult  to heat—avoids “bake-on”; abrasive slurries
  • Eliminates plugging and fouling of the heat transfer surface
  • Rapid response time
Indirect Heating
Direct Heating

Indirect Heating

Direct Heating

Types of Direct Steam Injection

Hydro-Thermal’s heaters utilize direct steam injection. This general term refers to any type of fluid heating that uses steam being directly mixed with water or process fluid. There are many forms of direct steam injection, including spargers, eductor pumps, externally modulated heaters, and internally modulated heaters. Each method varies in its levels of complexity, with sparging being the most simple and internally modulated, having the greatest level of technology and control.

Internal Modulation

Hydro-Thermal’s technology, which utilizes internal modulation, is the most advanced form of direct steam injection. It has many benefits over other direct heating methods, including:

  • Reduced steam consumption
  • Significantly lower energy costs, 100% efficient use of steam energy
  • Low maintenance
  • Handles fluids that are difficult to heat—avoids “burn-on”; highly viscous or abrasive slurries are no problem
  • Small footprint
  • Consistent, precise discharge temperature
  • No condensate return required
Direct Steam Injection - How it Works

SteamSparging

Steam Sparging is the oldest, most straightforward and least complicated technique for mixing steam with liquid or slurry to affect heating. It is injecting steam directly into a fluid-filled tank. Though considered inexpensive and straightforward, sparging is very inefficient, and the operation invariably results in:

  • Poor heat injection economics due to steam energy escaping from vessels without condensing.
  • High maintenance costs for tanks, sensors, and piping are the norm if the equipment operates outside the design parameters.
  • Equipment failure (both vessel and sparger pipes) due to the vibration associated with steam hammer when not operated within their narrow design envelope.
  • Usually less than satisfactory on/off process control. A sparger is the least controllable direct steam injection heating method.
  • Non-uniform heating
Sparging

Sparge Tube

The externally modulating sparger tube (MST) heater consists of a spring controlled, variable-injection sparger tube inside a cast process flow body. In response to a temperature sensor, the external flow control valve modulates the steam to a spring-loaded piston. MST heaters work reasonably well on clear liquids and some low solids solutions. Still, they are subject to severe clogging and steam hammer if frequent maintenance is not performed. In typical water heating applications, these devices typically require monthly tear down and acid bath cleaning. Since the steam flow is dependent upon a spring-loaded valve, accurate temperature control is difficult once the spring begins to wear.

Additionally, if low (trim heating) or high steam flow is required, the spring mechanism can have difficulty with accurate or stable control. Spring failure is a common issue with this type of heater. Additional drawbacks of sparge tubes are:

  • Requires external steam control valve
  • Very high maintenance
  • Prone to scaling and fouling
  • Steam hammer common
  • Limited temperature control due to external control
  • Internal spring prone to wear and breakage
Sparge Tube

Mixing Ts

Mixing Ts combine separate streams of steam and cold water to produce heated water. Because accurate temperature control is difficult to maintain with this method, mixing Ts is not the best choice for process fluids. When used for water, mixing tees are prone to scaling, fouling, and excessive hammer. Their operation often requires steam and water pressure to be very close to each other for balanced mixing. When either steam or water pressure fluctuates slightly, the higher pressure line can overcome the other and backfill the piping. This can result in live steam discharging the system. The drawback of Mixing Ts are:

  • Very high maintenance
  • Prone to scaling and fouling
  • Steam hammer is common
  • Potentially very dangerous due to live steam being close to human contact
  • Limited temperature control
Mixing T's

Want to learn more:

  • Benefits of direct steam injection button
  • Get a quote button
  • Contact Hydro-Thermal button
  • PDF Downloads - direct steam injection technology button
  • Videos button
  • Case Studies Button

 

HTC.logo.white1 01

Hydro-Thermal is the global leader in the development and manufacturing of Hydroheaters. Through our vast global channel partners, we support hydro heating in six continents and all industrialized areas. We create heating systems for a variety of industries including: pulp, paper, chemical, ethanol, food & beverage, metal, & more!

Hydro-Thermal Corporate 

400 Pilot Court
Waukesha, WI 53188 USA
Phone: (262) 548-8900
Fax: (262) 548- 8908